Brads Tiger

Post your questions or information about Tiger restorations
Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Tue Apr 14, 2015 5:03 pm

Looks like some quite extensive bodywork being chopping about as well, nice engineering though.
1966 Sunbeam Tiger Mk1

bigbob
Posts: 379
Joined: Wed Aug 19, 2009 11:31 am

Post by bigbob » Tue Apr 14, 2015 5:39 pm

There was a UK Tiger about, many years ago, with an E-Type IRS grafted on. Don't remember it being as professional as this though.

Tomaselli
Posts: 942
Joined: Fri Sep 30, 2005 2:03 pm
Location: Cheshire, North West England

Post by Tomaselli » Tue Apr 14, 2015 8:35 pm

Brad1380 wrote:The GT40 wheels arrived this morning, very nice.

Image
Very nice that, lovely colour combo :mrgreen:

Tomaselli
Posts: 942
Joined: Fri Sep 30, 2005 2:03 pm
Location: Cheshire, North West England

Post by Tomaselli » Tue Apr 14, 2015 8:35 pm

Tom_HRO260 wrote:Just in case you are interested, here's a couple of shots of the IRS getup.
WOW! Thanks for sharing Tom, I can't stop looking at those images!!

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Mon May 04, 2015 2:30 pm

After my repaired header tank failed a test i bought a replacement one from Paul ( Aka Red Race Tiger) as a new header is cheaper than an overheated engine, not that i have an engine at the moment....watch this space as they say )

The tank is a first rate peice of kit, the welding is excellent with no undercuts on the root & good penetration when you look inside, i am more than happy with it.

Image
1966 Sunbeam Tiger Mk1

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Sat Jun 13, 2015 6:57 pm

I was trying to encapsulate the exhaust chassis sections, when i cut the ovals to the right shape they wouldn't stay in place, if i make them longer i can push them to be a better fit then trim afterwards, is this the right way to do it?

Image
1966 Sunbeam Tiger Mk1

meadowhog
Posts: 392
Joined: Fri Dec 16, 2011 1:50 pm
Location: South Bucks

Post by meadowhog » Sun Jun 14, 2015 2:35 am

The only thing to be mindful of is the top bit which is impossible to weld until it's cut back.

User avatar
redbaron
Posts: 111
Joined: Sun Aug 16, 2009 6:18 pm
Location: Essex

Brads Tiger

Post by redbaron » Sun Jun 14, 2015 10:41 am

Hi Brad
by sleeving the exhaust hole through the chassis you will loose some of the clearance for the exhaust pipe.
The original pass through was open and reinforced with the cut out over piece.
Replacement repair sections do come with a larger hole and may be of benifit when fitting a larger exhaust pipe.

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Sun Jun 14, 2015 6:29 pm

I have opened the ovals up by about 1/8th of an inch, they are bigger than the reinforcing plates now, the idea was to try to keep some of the road gravel out of the chassis as i've found quite a lot of it so far.
1966 Sunbeam Tiger Mk1

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Tue Jun 23, 2015 9:08 pm

Well that end went ok, think i'll wait until the car is turned to do the other side as i don't like welding upside down.

Image
1966 Sunbeam Tiger Mk1

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Sun Jul 19, 2015 6:39 pm

Did the other side of the exhaust cut out.

Also tried to fill in a few holes in the n/s inner rear wing, cut back to what i thought was good metal but when i weded it all blew away, so ended up cutting the lot out.


Image

Image

I must have found at least 30 bits of gravel in the inner sill, what is the point of that great opening into it? Shouldn't it have a grommet?

Image

Lastly, ran the rear badges over the buffer on the 3rd rouge, they turned up alright.

Image

Image
1966 Sunbeam Tiger Mk1

bobvic
Posts: 4
Joined: Mon Mar 02, 2015 8:55 pm

Post by bobvic » Tue Jul 21, 2015 8:49 pm

The holes in the chassis sections are provided to accommodate a multitude of locating pegs and rods used to position same on the chassis bench prior to welding, no robots like today. Blanking off is not a problem but one must drill drain holes at the lowest points to evacuate water/condensation. I always plug mine and remove them occasionally.

Regarding the exhaust pass throughs I notice you have sleeved the holes but the steel on the bottom of the section looks well pitted. My Quals and experience as a Structural Engineer tells me that the maximum stress on a box section is at the most extreme position from the neutral axis. ie at the car floor and the very bottom of the section. Your photograph shows inadequacy in this area.

By way of interest I few years ago I had the pleasure of looking underneath one of the Le Mans Lister Tigers and saw what they had done in this area to accommodate what looked like 3inch pipes. They had cut away virtually all the two side limbs of the section generating a 4 inch gap for the pipes together with the bottom of the section and inserted a 5mm plate spanning and overlapping the gap, ie at the max stress position.
This seemed a satisfactory solution to me but the side limbs of the section would need to be flanged on the cut edges like on the Jensen standard version I could not see that this had been done on the Le Mans Tiger.

Finally you may want to consider cutting away the suspect metal at the bottom of the section and inserting a plate as described above that way you will have a stiffer than designed section together with a couple of good skid plates to boot.

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Wed Jul 22, 2015 9:33 pm

Welcome to the forum & thanks for your comments, to a fellow engineer i think those sections will be fine once the Jenson re-enforcement sections are added.T

Ths repair section only took 4 1/2 hrs to fabricate.....

Image
Last edited by Brad1380 on Thu Jul 23, 2015 6:18 pm, edited 1 time in total.
1966 Sunbeam Tiger Mk1

garyv8tiger
Posts: 650
Joined: Sun Dec 30, 2007 10:57 am

Post by garyv8tiger » Wed Jul 22, 2015 9:41 pm

Bit off topic but I was in Egypt last month .got chatting to a couple of lads from Birmingham.got onto cars the guy said his brother had one but sold it .i chirped up s his name ned .should have seen his face .yep it was neds .small world hey

Brad1380
Posts: 547
Joined: Wed Apr 27, 2011 1:38 pm

Post by Brad1380 » Thu Aug 06, 2015 7:21 pm

Nice little story that Gary, thanks for sharing it. I hope you told them it's in good hands.

Eventually found the time to sort out the front section of the RHS rear wing, still a bit of a high spot in the lead but i can't reach it properly off a ladder so will wait until the cars horizontal again.

Image
1966 Sunbeam Tiger Mk1

Post Reply