Track days exhaust

Post any Tech Tips or any matters and questions relating to upkeep
Post Reply
bigbob
Posts: 379
Joined: Wed Aug 19, 2009 11:31 am

Track days exhaust

Post by bigbob » Thu Feb 06, 2014 5:51 pm

Any ideas/experience of getting exhaust noise down to 105db for up coming track day? Running twin 2 1/2" pipes with "cherry bombs" Suspect well over 105 at present!

JAYANDSHEL
Posts: 173
Joined: Mon Mar 02, 2009 8:18 pm
Location: Kent

Post by JAYANDSHEL » Thu Feb 06, 2014 6:01 pm

I have same concerns and was going to try Supertraps, they bolt into the tail pipe and are a selection of disc's that you add or take away to tune the noise. more disc's equals more noise.
I have not bought them yet but this is my plan

User avatar
pushrod
Posts: 226
Joined: Wed Jan 18, 2012 12:54 am
Location: South Wales

Post by pushrod » Thu Feb 06, 2014 7:16 pm

Whilst I'm not saying you should do this now. When I used to rally back in the 70/80's if a car failed scrutineering due to a noisy exhaust we used to shove brillo pads up the tailpipe.

Marshals had to be careful on the event as the pads often shot out of the exhaust pipe when the car passed.

Ahh those were the days - no Health and Safety back then.

Lou.
65 Mk1 Tiger 260
66 Mk1 Tiger 260 (African Violet)
63 Ford Falcon Sprint
63 Ford Falcon Monte Carlo Rally replica
02 Honda Valkyrie

bigbob
Posts: 379
Joined: Wed Aug 19, 2009 11:31 am

Post by bigbob » Fri Feb 07, 2014 10:37 am

I did wonder about these
https://www.merlinmotorsport.co.uk/p/me ... -ex-muff-4
Look easy to fit, but not sure if reduction would be enough.

H, Sunny 65
Posts: 110
Joined: Mon Mar 10, 2008 11:40 pm

Post by H, Sunny 65 » Fri Feb 07, 2014 12:21 pm

Plenty of free APP's for smart phones, out there to measure db's.
I have a couple on my phone, not measured my Tiger noise yet, but may fire it up to over the weekend to see what noise it makes.
Wire wool in a coke can with holes over end and j/clip to end of pipes works for noise reduction. .[that method a bit more you Bob, than the fancy pipes you saw]
Harry

bigbob
Posts: 379
Joined: Wed Aug 19, 2009 11:31 am

Post by bigbob » Sun Feb 09, 2014 12:59 pm

I like your style. I think a pair of large beer cans would suit better though. But worried they would create a lot of back pressure & be a bugger to fit securely. But definitely worth investigating.

Tomaselli
Posts: 942
Joined: Fri Sep 30, 2005 2:03 pm
Location: Cheshire, North West England

Post by Tomaselli » Sun Feb 09, 2014 6:13 pm

Good idea Harry. I will try an App on my iPhone over the weekend. To get a fair comparison needed for track day regulations, how far away do you have to be with the decibel reader, and what revs needed from the engine?

Sure I won't have a problem :mrgreen:

JAYANDSHEL
Posts: 173
Joined: Mon Mar 02, 2009 8:18 pm
Location: Kent

Post by JAYANDSHEL » Sun Feb 09, 2014 6:28 pm

Its measured 1meter away and at 45degrees vertical from the tailpipe.
revs depend on the tester/circuit sometimes they ask for the max revs and then work out 2/3 of that or they ask for 4500.
Jay
Last edited by JAYANDSHEL on Sun Feb 09, 2014 6:30 pm, edited 1 time in total.

Tomaselli
Posts: 942
Joined: Fri Sep 30, 2005 2:03 pm
Location: Cheshire, North West England

Post by Tomaselli » Sun Feb 09, 2014 6:30 pm

Cheers, what revs do I need. Mine is awfully quiet until about 1000 rpm ;)

Tomaselli
Posts: 942
Joined: Fri Sep 30, 2005 2:03 pm
Location: Cheshire, North West England

Post by Tomaselli » Sun Feb 09, 2014 10:22 pm

OK, I have it now - 4,500 rpm will be a challenge. Couple of brillo pads in a coke can might be the fix, :mrgreen:

User avatar
pushrod
Posts: 226
Joined: Wed Jan 18, 2012 12:54 am
Location: South Wales

Post by pushrod » Sun Feb 09, 2014 10:42 pm

According to the MSA regulations:

“the sound test shall be conducted as set out within these regulations with the engine running at 3/4 maximum speed, the sound level meter at a height of 0.5 metres above the ground (± 0.1 metre) located at 45° to and 0.5 metres distant from the exhaust”.

That way the scruitineer doesn’t kop a mouthful of Brillo Pad!

Incidentally if you have a Mk1Tiger ¾ maximum is around 3500rpm.
Oh and don’t rely on one of those phone apps as they usually max out at 105db.

Lou.
65 Mk1 Tiger 260
66 Mk1 Tiger 260 (African Violet)
63 Ford Falcon Sprint
63 Ford Falcon Monte Carlo Rally replica
02 Honda Valkyrie

bigbob
Posts: 379
Joined: Wed Aug 19, 2009 11:31 am

Post by bigbob » Mon Feb 10, 2014 10:31 am

Apparently twin turbos tend to quieten down the exhaust. Seems like a good excuse to me.

V Mad
Posts: 141
Joined: Fri Oct 14, 2005 6:21 pm
Location: Surrey
Contact:

Post by V Mad » Sun Feb 23, 2014 6:51 pm

Just swap the rev counter for a 4-cylinder one. Halves the revs (oh no it doubles doesnt it? Maybe a 12 cyl one then) :wink: I could easily recal a four to make it read much lower

Re wire wool, it is so fine it might catch fire. I bought some stainless steel pan scourers at Aldi that could be be worth a try? :D
Chris :-)
1966 Mk1 260 Tiger
!972 Triumph Stag 3.0V8
www.stagweber.co.uk

Post Reply